Sandvik Tamrock HL300 Drifter Parts supply for older compact drilling equipment where continued operation depends on practical sourcing and careful identification of service parts. We support purchasing and maintenance teams with part-number checking, OEM-equivalent aftermarket options where applicable, fast quotation and worldwide shipping.
KEEP YOUR HL300 MAINTENANCE MOVING
Vomeks supplies replacement parts for Sandvik Tamrock HL300 hydraulic drifter applications. We support international purchasing and maintenance teams with part-number checking, quotation, OEM-equivalent aftermarket options where applicable, and worldwide shipping.
HL300 requirements may include gear housing assemblies, rotation bushings, couplings, rotation shafts, gears, shank rods, drill sleeves, pistons, front and rear cylinders, seals, seal kits, flushing components, accumulators, hydraulic motor components, bearings, valves, bushings and related wear or service parts. The component examples shown below can help define the required part group before quotation.
For accurate identification, send the HL300 part number, quantity and any available component or machine identification. If the reference is uncertain, photos of the removed part, identification marks, dimensions or related assembly information can help organize the request for checking before quotation.
Send the required part number, quantity and destination country for quotation. Where applicable, we can evaluate replacement or aftermarket supply options against the supplied reference and arrange export-oriented worldwide delivery.
Worldwide Delivery: Europe, North America, South America, Africa, Australia / Oceania, Asia, Middle East
GEAR HOUSING ASSY
ROTATION BUSHING
COUPLING
ROTATION SHAFT
GEAR
SHANK ROD
SHEATH
CLAMP
NEEDLE BEARING
TIE ROD
DRILL SLEEVE
DISTRIBUTOR
FRONT CYLINDER
REAR CYLINDER
PISTON
ROD SEAL
HEXAGON HEAD BOLT
HEXAGON NUT
HOSE CLIP
ADAPTER
FRONT COVER
FLUSHING DEVICE
U SEAL
SHANK BUSHING
SEAL
FLUSHING ADAPTER
STRAIGHT THREAD CONNECTOR
SWIVEL NUT ELBOW
GREASE NIPPLE
ACCUMULATOR
DIAPHRAGM
VALVE
RUBBER CAP
SEAL KIT FOR ROCK DRILL
BUSHING
TAPERED ROLLER BEARING
SHAFT NUT
LOCK PLATE
LOCK WASHER
SHAFT SEAL
BANJO ADAPTER
BOLT
GASKET PLATE
HEXAGON HEAD SCREW
HYDRAULIC MOTOR
SCREW
SHAFT
GEAR WHEEL SET
VALVE DRIVE
DISC VALVE
PLATE
PIN
O-RING
SPACER
SPRING WASHER
HOUSING
PLUG
EXTENSION ROD
FILLING DEVICE
PICK SET
PULLER
GAUGE
TOOL SET
PUNCH
FITTING PLATE
For Sandvik Tamrock HL300 Drifter Parts, purchasing decisions are usually driven by downtime risk, identification accuracy and the condition of the surrounding assembly. This page is intended to help buyers move from a maintenance requirement to a correctly defined parts request without turning the page into a generic technical manual.
Depending on inspection findings, attention may focus first on bushings, seals, small wear parts, and bearing components. The correct order should follow the actual wear pattern and the reference found on the removed component rather than a generic parts list alone.
Maintenance teams should investigate increased play, minor oil seepage becoming persistent, or roughness noticed during manual inspection. These symptoms do not identify a single failed part by themselves, but they help define which assembly should be inspected before a purchase decision is made.
Replace inexpensive wear items before excessive clearance damages harder-to-source mating components. For international orders, include the model, part number, quantity and any useful machine or component identification so the quotation can be checked before shipment.
Related Sandvik pages: Sandvik Tamrock HLX5 Drifter Parts | Sandvik Tamrock DX700 Spare Parts | Sandvik Tamrock HL1010 Drifter Parts
Send the HL300 part number, quantity, destination country and any available identification marks, dimensions or component photos. We will organize the requirement for verification and quotation.
We are ready to serve you on Monday to Friday from 08:30 to 18:30, 7/24 you can contact us at info@vomeks.com